ROCKPI-N8

This tutorial will show the details of Radxa ROCKPI-N8 board with VMARC RK3288 SOM.

Hardware details and wiki ROCKPI-N8

Hardware Access

../../../_images/rock-pi-n8.jpg

BSP Building

Host require few tools/packages to build BSP, install them from host

U-Boot

$ git clone https://github.com/amarula/u-boot-amarula
$ cd u-boot-amarula
$ git checkout -b rock-pi origin/rock-pi
$ make rock-pi-n8-rk3288_defconfig
$ make

Linux

$ git clone https://github.com/amarula/linux-amarula.git
$ cd linux-amarula
$ git checkout -b rockpi origin/rockpi
$ make mrproper
$ ARCH=arm make multi_v7_defconfig
$ ARCH=arm make LOADADDR=0x02000000 uImage dtbs -j 4

Buildroot

$ git clone git://git.buildroot.net/buildroot
$ cd buildroot
$ make rock_pi_n8_defconfig
$ make

SD Boot

In the output/images directory, flash sdcard.img on to micro sd

$ sudo dd if=output/images/sdcard.img of=/dev/sdX status=progress (X - find it from fdisk -l)
$ sync

VMARC RK3288 SOM used on this board looks for images on EMMC and then SD(EMMC is the first in boot order). If EMMC has a valid image then it boots from EMMC. To make SD boot, follow the below link to erase EMMC. It is also valid for RK3288.

EMMC erase notes RK3288 EMMC

Put the micro-SD card onto your board in the slot and power the board. You should see something like:

U-Boot TPL 2020.07-rc4 (Jul 06 2020 - 18:50:52)
Trying to boot from BOOTROM
Returning to boot ROM...
Trying to boot from MMC1


U-Boot 2020.07-rc4 (Jul 06 2020 - 18:50:52 +0530)

SoC: Rockchip rk3288
Reset cause: RST
Model: Radxa ROCK Pi N8
DRAM:  4 GiB
PMIC:  RK808
MMC:   dwmmc@ff0c0000: 1, dwmmc@ff0f0000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial@ff690000
Out:   serial@ff690000
Err:   serial@ff690000
Model: Radxa ROCK Pi N8
Net:   No ethernet found.

Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc1(part 1) is current device
Scanning mmc 1:3...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
146 bytes read in 5 ms (30.4 KiB/s)
1:     RK3399_ROCKPI_N8
Retrieving file: /uImage
9396800 bytes read in 616 ms (14.5 MiB/s)
append: console=ttyS2,115200n8 root=/dev/mmcblk0p4 rw rootwait
Retrieving file: /rk3288-rock-pi-n8.dtb
39356 bytes read in 18 ms (2.1 MiB/s)
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
Loading Device Tree to 0fff3000, end 0ffff9bb ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x500
[    0.000000] Linux version 5.7.0-rc1 (suniel@suniel-P5WE0) (gcc version 9.3.0 (Buildroot 2020.08-git-00494-g07339c7-dirty), GNU ld (GNU Binutils) 2.0
[    0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Radxa ROCK Pi N8
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 64 MiB at 0xfa000000
[    0.000000] percpu: Embedded 20 pages/cpu s49356 r8192 d24372 u81920
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1038848
[    0.000000] Kernel command line: console=ttyS2,115200n8 rw rootwait root=/dev/mmcblk0p4 rootfstype=ext4
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 4038496K/4161536K available (13312K kernel code, 1792K rwdata, 5452K rodata, 2048K init, 403K bss, 57504K reserved, 65536K cma-)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x300/0x4a4 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000022] Switching to timer-based delay loop, resolution 41ns
[    0.005949] Console: colour dummy device 80x30
[    0.005997] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.006014] pid_max: default: 32768 minimum: 301
[    0.006180] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.006199] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.006915] CPU: Testing write buffer coherency: ok
[    0.006950] CPU0: Spectre v2: using BPIALL workaround
[    0.007167] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[    0.007920] Setting up static identity map for 0x300000 - 0x3000ac
[    0.009927] rcu: Hierarchical SRCU implementation.
[    0.014334] EFI services will not be available.
[    0.014553] smp: Bringing up secondary CPUs ...
[    0.016215] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[    0.016223] CPU1: Spectre v2: using BPIALL workaround
[    0.018003] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[    0.018011] CPU2: Spectre v2: using BPIALL workaround
[    0.019761] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[    0.019770] CPU3: Spectre v2: using BPIALL workaround
[    0.019910] smp: Brought up 1 node, 4 CPUs
[    0.019923] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[    0.019931] CPU: All CPU(s) started in SVC mode.
[    0.020624] devtmpfs: initialized
[    0.029817] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[    0.030125] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.030146] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.032048] pinctrl core: initialized pinctrl subsystem
[    0.034138] thermal_sys: Registered thermal governor 'step_wise'
[    0.034814] DMI not present or invalid.
[    0.035247] NET: Registered protocol family 16
[    0.037639] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.040375] cpuidle: using governor menu
[    0.041044] No ATAGs?
[    0.041180] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.041194] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.044438] Serial: AMBA PL011 UART driver
[    0.107102] AT91: Could not find identification node
[    0.107815] vcc5v0_sys: supplied by vcc12v_dcin
[    0.108269] vbus_host: supplied by vcc5v0_sys
[    0.108709] vbus_typec: supplied by vcc5v0_sys
[    0.112010] iommu: Default domain type: Translated
[    0.113458] vgaarb: loaded
[    0.114414] SCSI subsystem initialized
[    0.114875] usbcore: registered new interface driver usbfs
[    0.114929] usbcore: registered new interface driver hub
[    0.114998] usbcore: registered new device driver usb
[    0.116660] pps_core: LinuxPPS API ver. 1 registered
[    0.116671] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.116694] PTP clock support registered
[    0.116905] EDAC MC: Ver: 3.0.0
[    0.120011] clocksource: Switched to clocksource arch_sys_counter
[    1.361978] NET: Registered protocol family 2
[    1.362638] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    1.362677] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    1.362759] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.362950] TCP: Hash tables configured (established 8192 bind 8192)
[    1.363059] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.363112] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.363313] NET: Registered protocol family 1
[    1.363779] RPC: Registered named UNIX socket transport module.
[    1.363791] RPC: Registered udp transport module.
[    1.363799] RPC: Registered tcp transport module.
[    1.363806] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.363818] PCI: CLS 0 bytes, default 64
[    1.364888] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available
[    1.366309] Initialise system trusted keyrings
[    1.366489] workingset: timestamp_bits=30 max_order=20 bucket_order=0
[    1.374312] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.375102] NFS: Registering the id_resolver key type
[    1.375130] Key type id_resolver registered
[    1.375139] Key type id_legacy registered
[    1.375157] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.375192] ntfs: driver 2.1.32 [Flags: R/O].
[    1.375649] Key type asymmetric registered
[    1.375661] Asymmetric key parser 'x509' registered
[    1.375719] bounce: pool size: 64 pages
[    1.375761] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.375771] io scheduler mq-deadline registered
[    1.375779] io scheduler kyber registered
[    1.410568] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.410588] dma-pl330 ff250000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.411318] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.411336] dma-pl330 ffb20000.dma-controller:       DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[    1.476400] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    1.479637] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 34, base_baud = 1500000) is a 16550A
[    1.480908] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 35, base_baud = 1500000) is a 16550A
[    2.243259] printk: console [ttyS2] enabled
[    2.250329] SuperH (H)SCI(F) driver initialized
[    2.256667] msm_serial: driver initialized
[    2.261506] STMicroelectronics ASC driver initialized
[    2.268898] STM32 USART driver initialized
[    2.291052] brd: module loaded
[    2.303028] loop: module loaded
[    2.319631] libphy: Fixed MDIO Bus: probed
[    2.325424] CAN device driver interface
[    2.330915] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[    2.338665] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    2.345225] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.351925] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
[    2.359706] igb: Copyright (c) 2007-2014 Intel Corporation.
[    2.369300] clk: failed to reparent mac_clk to clkin_gmac: -22
[    2.375909] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found
[    2.382960] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock
[    2.389706] rk_gmac-dwmac ff290000.ethernet: phy regulator is not available yet, deferred probing
[    2.402427] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    2.410763] usbcore: registered new interface driver pegasus
[    2.417131] usbcore: registered new interface driver asix
[    2.423226] usbcore: registered new interface driver ax88179_178a
[    2.430100] usbcore: registered new interface driver cdc_ether
[    2.436665] usbcore: registered new interface driver smsc75xx
[    2.443159] usbcore: registered new interface driver smsc95xx
[    2.449616] usbcore: registered new interface driver net1080
[    2.455998] usbcore: registered new interface driver cdc_subset
[    2.462673] usbcore: registered new interface driver zaurus
[    2.468953] usbcore: registered new interface driver cdc_ncm
[    2.477943] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator
[    2.486027] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator
[    2.560245] dwc2 ff540000.usb: DWC OTG Controller
[    2.565532] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1
[    2.573477] dwc2 ff540000.usb: irq 40, io mem 0xff540000
[    2.580259] hub 1-0:1.0: USB hub found
[    2.584495] hub 1-0:1.0: 1 port detected
[    2.589512] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator
[    2.597607] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator
[    2.740075] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM
[    2.748493] dwc2 ff580000.usb: DWC OTG Controller
[    2.753810] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2
[    2.761741] dwc2 ff580000.usb: irq 41, io mem 0xff580000
[    2.768445] hub 2-0:1.0: USB hub found
[    2.772706] hub 2-0:1.0: 1 port detected
[    2.778361] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.785686] ehci-pci: EHCI PCI platform driver
[    2.790723] ehci-platform: EHCI generic platform driver
[    2.796796] ehci-platform ff500000.usb: EHCI Host Controller
[    2.803172] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3
[    2.812123] ehci-platform ff500000.usb: irq 38, io mem 0xff500000
[    2.840039] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00
[    2.847692] hub 3-0:1.0: USB hub found
[    2.851953] hub 3-0:1.0: 1 port detected
[    2.856922] ehci-orion: EHCI orion driver
[    2.861647] SPEAr-ehci: EHCI SPEAr driver
[    2.866306] ehci-st: EHCI STMicroelectronics driver
[    2.871956] ehci-exynos: EHCI Exynos driver
[    2.876803] ehci-atmel: EHCI Atmel driver
[    2.881485] tegra-ehci: Tegra EHCI driver
[    2.886165] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.893109] ohci-pci: OHCI PCI platform driver
[    2.898126] ohci-platform: OHCI generic platform driver
[    2.904228] ohci-platform ff520000.usb: Generic Platform OHCI controller
[    2.911768] ohci-platform ff520000.usb: new USB bus registered, assigned bus number 4
[    2.920775] ohci-platform ff520000.usb: irq 39, io mem 0xff520000
[    2.994823] hub 4-0:1.0: USB hub found
[    2.999060] hub 4-0:1.0: 1 port detected
[    3.004063] SPEAr-ohci: OHCI SPEAr driver
[    3.008740] ohci-st: OHCI STMicroelectronics driver
[    3.014403] ohci-atmel: OHCI Atmel driver
[    3.019874] usbcore: registered new interface driver usb-storage
[    3.033736] i2c /dev entries driver
[    3.041510] rtc-hym8563 1-0051: no valid clock/calendar values available
[    3.049179] rtc-hym8563 1-0051: registered as rtc0
[    3.054877] rtc-hym8563 1-0051: no valid clock/calendar values available
[    3.062400] rtc-hym8563 1-0051: hctosys: unable to read the hardware clock
[    3.073046] rk808 0-001b: chip id: 0x0
[    3.081112] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    3.088053] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    3.095061] DCDC_REG1: supplied by vcc5v0_sys
[    3.100702] DCDC_REG2: supplied by vcc5v0_sys
[    3.106147] DCDC_REG3: supplied by vcc5v0_sys
[    3.111304] DCDC_REG4: supplied by vcc5v0_sys
[    3.116788] LDO_REG1: supplied by vcc5v0_sys
[    3.122842] LDO_REG2: supplied by vcc5v0_sys
[    3.127809] vcca_codec: Bringing 1800000uV into 3300000-3300000uV
[    3.135696] LDO_REG3: supplied by vcc5v0_sys
[    3.141635] LDO_REG4: supplied by vcc_io
[    3.146994] LDO_REG5: supplied by vcc_io
[    3.152555] LDO_REG6: supplied by vcc5v0_sys
[    3.158297] LDO_REG7: supplied by vcc5v0_sys
[    3.164258] LDO_REG8: supplied by vcc5v0_sys
[    3.170045] SWITCH_REG1: supplied by vcc_io
[    3.175010] SWITCH_REG2: supplied by vcc_io
[    3.184612] vccio_flash: supplied by vcc_io
[    3.202185] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 500000 KHz
[    3.210703] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 600000 KHz
[    3.222909] sdhci: Secure Digital Host Controller Interface driver
[    3.229815] sdhci: Copyright(c) Pierre Ossman
[    3.236600] Synopsys Designware Multimedia Card Interface Driver
[    3.244558] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode.
[    3.252480] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller.
[    3.259869] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a
[    3.266124] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 30,32 bit host data width,256 deep fifo
[    3.289946] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    3.314279] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode.
[    3.322230] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller.
[    3.329626] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a
[    3.335891] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 31,32 bit host data width,256 deep fifo
[    3.346703] mmc_host mmc1: card is non-removable.
[    3.360313] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    3.364588] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    3.371238] mmc0: new high speed SD card at address 0002
[    3.387742] mmcblk0: mmc0:0002 00000 1.87 GiB
[    3.394650] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.402353] ledtrig-cpu: registered to indicate activity on CPUs
[    3.409628] usbcore: registered new interface driver usbhid
[    3.415868] usbhid: USB HID core driver
[    3.422432] drop_monitor: Initializing network drop monitor service
[    3.423601] GPT:Primary header thinks Alt. header is not at the end of the disk.
[    3.429751] NET: Registered protocol family 10
[    3.437705] GPT:524320 != 3911679
[    3.437706] GPT:Alternate GPT header not at the end of the disk.
[    3.437708] GPT:524320 != 3911679
[    3.437709] GPT: Use GNU Parted to correct GPT errors.
[    3.437727]  mmcblk0: p1 p2 p3 p4
[    3.442984] Segment Routing with IPv6
[    3.470324] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.477160] NET: Registered protocol family 17
[    3.482131] can: controller area network core (rev 20170425 abi 9)
[    3.484792] random: fast init done
[    3.489056] NET: Registered protocol family 29
[    3.497786] can: raw protocol (rev 20170425)
[    3.502554] can: broadcast manager protocol (rev 20170425 t)
[    3.506339] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
[    3.508873] can: netlink gateway (rev 20190810) max_hops=1
[    3.521025] mmc1: new high speed MMC card at address 0001
[    3.526067] Key type dns_resolver registered
[    3.532240] mmcblk1: mmc1:0001 SLD32G 28.9 GiB
[    3.536763] ThumbEE CPU extension supported.
[    3.541953] mmcblk1boot0: mmc1:0001 SLD32G partition 1 4.00 MiB
[    3.546508] Registering SWP/SWPB emulation handler
[    3.553368] mmcblk1boot1: mmc1:0001 SLD32G partition 2 4.00 MiB
[    3.558599] Loading compiled-in X.509 certificates
[    3.565141] mmcblk1rpmb: mmc1:0001 SLD32G partition 3 4.00 MiB, chardev (235:0)
[    3.580223] clk: failed to reparent mac_clk to clkin_gmac: -22
[    3.582322]  mmcblk1: p1 p2 p3 p4 p5
[    3.586767] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found
[    3.597702] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock
[    3.604474] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input).
[    3.612356] rk_gmac-dwmac ff290000.ethernet: TX delay(0x28).
[    3.618675] rk_gmac-dwmac ff290000.ethernet: RX delay(0x11).
[    3.625001] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no).
[    3.631924] rk_gmac-dwmac ff290000.ethernet: cannot get clock clk_mac_speed
[    3.639698] rk_gmac-dwmac ff290000.ethernet: clock input from PHY
[    3.651511] rk_gmac-dwmac ff290000.ethernet: init for RGMII
[    3.657839] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[    3.665826] rk_gmac-dwmac ff290000.ethernet:         DWMAC1000
[    3.671668] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported
[    3.680031] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported
[    3.688389] rk_gmac-dwmac ff290000.ethernet: COE Type 2
[    3.694226] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported
[    3.702101] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported
[    3.709305] rk_gmac-dwmac ff290000.ethernet: Normal descriptors
[    3.715919] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled
[    3.722435] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    3.731383] rk_gmac-dwmac ff290000.ethernet: device MAC address 76:ec:85:f3:b0:94
[    3.843959] libphy: stmmac: probed
[    3.847845] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    3.861869] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[    3.877357] dw-apb-uart ff690000.serial: forbid DMA for kernel console
[    3.904177] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
[    3.913251] VFS: Mounted root (ext4 filesystem) on device 179:4.
[    3.922533] devtmpfs: mounted
[    3.927824] Freeing unused kernel memory: 2048K
[    3.971529] Run /sbin/init as init process
[    4.134971] EXT4-fs (mmcblk0p4): re-mounted. Opts: (null)
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Saving random seed: [    5.214934] random: dd: uninitialized urandom read (512 bytes read)
OK
Starting system message bus: [    5.269464] random: dbus-uuidgen: uninitialized urandom read (12 bytes read)
[    5.277635] random: dbus-uuidgen: uninitialized urandom read (8 bytes read)
dbus-daemon[177]: Failed to start message bus: Could not get UID and GID for username "dbus"
done
Starting network: OK

Welcome to ROCKPI-N8..!!
rockpi-n8 login:

use root for login.